Last week was such a great week. I got to meet the infamous Papajam and his wife, Jaci. We worked our hinnies off the entire time they were here. Each night, we went to bed exhausted.
We started off the first day by looking things over and outlining the plan. Brakes were to be completed first because we didn’t want to have to deal with any issues with the brake lines once the engine was installed. Next, we would get the engine and transmission installed then deal with any wiring issues. I had replaced several wires on the harness and was concerned that I may have gotten a few of them out of place.
Jim checked the calipers and installed the brake pads while I ran back and forth to the basement to bring everything up we needed. I disassembled the hand brake mechanism, cleaned it, added fresh lithium grease and reassembled it. We used one of IAP’s pressure bleeders to bleed the brake system. It’s a great tool that should be used in conjunction with good old fashioned foot pumping. We left the pressure bleeder hooked up all night with the brake pedal depressed to allow any air bubbles to work their way up and out.
Next, Jim had me running back down to the basement to haul up the bits we needed to put on the engine. This was the easiest time to set the bell crank and pump gap. Jim also showed me how to synchronize the butterflies without the aid of an expensive tool. Next came the exhaust manifold that I had painted with Eastwood’s manifold paint. They look like new. After that was done, we mated the tranny to the back of the engine. In the pictures you can see that the bearing, retainer and folk are put together and then slid over the input shaft. A small amount of lithium grease was applied to the shaft splines. Jim took great care to make sure that the fork engaged the pivot.
We put the front of the car on some two by sixes to gain some clearance for the engine hoist. Then, we raised the back of the car as far as we could. Even then, it wasn’t quite enough, but we made it work. We raised the engine up and that’s when the fun began. The scariest part of installing an engine is when it is dangling over the expensive body work. Once we got it down into the engine bay, we ran into a few things that I should not have installed until after the engine was in. We, we removed those items and eventually wrestled the engine and transmission in. On it’ way in, it bounced off the lower radiator cross member. A little touchup paint fixed that. Once the radiator was installed and hooked up, the chipped paint seemed to have disappeared. While we were wrestling with the engine, Jaci was snapping pictures and keeping a sharp eye out. She was a great help.
Next we installed an IMASAF three piece exhaust system from Centerline. Apparently, Centerline purchases one front section to use on more than one car. We found out that 25 centimeters had to be removed from the back of the front part. It seems like a pretty cheesey to me. See the picture of Papajam with the wheelie cutter. Long after I got the system, a buddy of mine warned me that this brand of exhaust fit poorly at the manifold. Had we not known about this, we could have cracked the manifold when we tightened up the bolts. Even installing two copper gaskets wasn’t enough to stop it from leaking. The system is going in the trash and I will be purchasing a quality CISAM exhaust system from Conti or IAP.
Next we installed an IMASAF three piece exhaust system from Centerline. Apparently, Centerline purchases one front section to use on more than one car. We found out that 25 centimeters had to be removed from the back of the front part. It seems like a pretty cheesey to me. See the picture of Papajam with the wheelie cutter. Long after I got the system, a buddy of mine warned me that this brand of exhaust fit poorly at the manifold. Had we not known about this, we could have cracked the manifold when we tightened up the bolts. Even installing two copper gaskets wasn’t enough to stop it from leaking. The system is going in the trash and I will be purchasing a quality CISAM exhaust system from Conti or IAP.
Beautiful job! I just went through the same thing with a CISAM from IAP. The fit at the manifold was fine but I had to shorten mine by about 8" for it to fit in my 69 1750 GTV. I think it was actually designed for a Berlina. Even after getting the length right, the angle of the down pipe is wrong so that the center section rubs up against the heat shields. I'm going to have to take it to a shop to have the angles made right. Bottom line--I'm not sure CISAM is the answer. What's more, it was Centerline who filled me in on the angle issues and was very helpful in telling me about the unique angles of needed for different year cars. Anyway, good luck. I'm very very envious of that beauty you've got.
Next, Jim got to hookin up the wires in the engine compartment. I focused my attention on the hose clamps that I had plated. I found used the best of the fasteners from a very large pile of used clamps. I think they look terrific.
After those were assembled, I got after the fuse box. I cleaned all of the contacts and installed some new fueses. I had already added a wire for the cut-off solenoid, but I needed to wire it to the fues box. I made a jumper wire to get power to the auxiliary fuse panel and used the slot for the fog lights.
All this time we had been working on the car, I wasn’t very excited. It has been such a long tough road that it was going to take a lot to get me excited. We were having a great time, but the excitement was lacking, until I had to add gasoline to the gas tank. It was a moment I had been waiting for 13 years. We hooked up the battery and the ignition switch. I turned the switch, expecting to hear the fuel pump whir. Crap, the fuel pump was dead. No worries, I’ve got one “one the shelf”. The new fuel pump whirred to life and we checked for leaks. After tightening up some of the fittings, Jim removed the spark plugs. We cranked the engine to build up the oil pressure. It seemed to take for ever, but it finally came up. For some strange reason the words “go for throttle up” popped in my head. Jim put the plugs in and hooked up the wires. I turned the ignition and the engine popped right off. It was a great moment and I almost cried. Even Jim lit up. After running the engine and look for more leaks, Jim torqued the head nuts (not to be confused with hot nuts – that’s an inside joke).
Papajam and Jaci were more than a tremendous help. It was more than apparant that Jaci had been watching Papa work on cars and paying attention. On numerous occasions she would make comments or correct something I was doing wrong. Without their help, I would have been floundering for months on this. I am so grateful for their help. Thank you Papa and Jaci.
Papajam and Jaci were more than a tremendous help. It was more than apparant that Jaci had been watching Papa work on cars and paying attention. On numerous occasions she would make comments or correct something I was doing wrong. Without their help, I would have been floundering for months on this. I am so grateful for their help. Thank you Papa and Jaci.
This is great. The car is beautiful. Its always great to take a week off and work on your car, but to get a guru to come help? It doesnt get any better than that.
What an exciting day it must have been to finally drop that beautiful lump of a motor into that spotless engine bay!! I must admit that those pictures of the engine/tranny dangling over the car made my palms sweat.
Did someone say Papajam's on tour with Jaci? Heck, if that's the case, I can arrange some cases of beer if they would like to help me with my brakes this weekend. ha!
What a great guy for taking some time off to help you Osso. 13 years, eh? That be a long time, but it's finally here. Can't wait to see the finished product in the near future, especially at the pace you're rippin' through it!
Osso - You already know that you probably have the best duetto in the world - all of us are in awe of your attention to detail, your tenaciousness and your sheer bloody mindedness in seeing this project through.
It must be so inspiring for you not only to see the light at the end of the tunnel, but also now to hear the engine roar echoing off the tunnel walls.
And you, in turn, are inspiring alfisti the world over.
Well done. Do medals exist for this sort of project?
This has been an amazing story, following your trials and tribulations over the years. I am in awe of your talents, skills and tenacity, and I can see it is paying off. I am so happy for you and hope to meet you one day and view this incredible work of heart in person.
I am raising my coffee mug (at work) and toasting to you achievement.
Thank you for sharing with all of us. It has been an inspiration for me and one day I would like to do the same...only not as long.
I sincerely hope she drives as good as she looks.
I know your supposed to drive 'em and all but HOLY SMOKES everything is so nice, clean and shiny
I say keep it trailer queen You guys are always welcome in my garage.
I am in AWE! All the toil, and now the payoff - you get to enjoy your beautiful machine. Hope to see it in person in Detroit this year, Chicago next year, or maybe I'll get to visit it at home when I come to Golden this summer.
Make sure that when installing the exhaust, check the fit of the manifold and the frt pipe. Sometimes the frt pipe has to be massaged to fit. When it is proper, the frt pipe wil fit flat in the manifold. Use 2 gaskets is also good, and tighten the manifold to the frt pipe first. Great work and keep us informed, Good Luck!
Thanks for all of the compliments and praise. It's been a very difficult journey. Papajam and Jaci's help created the spark that has rekindled the love affair. I hope to continue to make progress over the next month or so.
There were three set of eyes on the installation of the exhaust. The gap between the header flange and the down pipes flange was at the top, not the base. In order to get the down pipes to bolt to the header, we raised the rear of the down pipes to close the gap. It hit the exhaust shield. My preference is to buy a better quality exhaust.
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Related Threads
?
?
?
?
?
Alfa Romeo Forums
2.1M posts
88.6K members
Since 2002
A forum community dedicated to Alfa Romeo owners and enthusiasts. Come join the discussion about performance, parts, modifications, troubleshooting, maintenance, and more!