This is my GTV which Im still building the engine bay is detailed with gold plating is has the largest street cam made by PACE cam shafts in melbourne the gearbox and diff ahve been rebuilt its lowered and ride on lenzo's whaich have been custom drilled and off set the car also has race seats and harness with a 6point cage.
My GTV pic
1 - 5 of 5 Posts
Joined
·
148 Posts
By creating a photobucket account ( Image hosting, free photo sharing & video sharing at Photobucket ), it's quite easy to resize photographs for the web, and it's a nice backup to your own hard drive so you don't lose those pics.
Oh, and I love that shade of green.
cheers,
scott
Oh, and I love that shade of green.
cheers,
scott
Joined
·
2,076 Posts
Garth & Kel: Nice looking 'fetta - what's up with the split front bumper?
BTW: By location, BJWhite meant where are you located? You should enter in your user CP a location so that it shows up on the right hand side of the header on your posts. By your mention of Melbourne and Adelaide, you're obviously in Australia (though we 0do have a Melbourne in FL here in the states). It's nice to know where people are located, for a number of reasons - but especially since cars imported to different countries had different set ups/equipment, and it'll help when answering questions etc. in the future...
BTW: By location, BJWhite meant where are you located? You should enter in your user CP a location so that it shows up on the right hand side of the header on your posts. By your mention of Melbourne and Adelaide, you're obviously in Australia (though we 0do have a Melbourne in FL here in the states). It's nice to know where people are located, for a number of reasons - but especially since cars imported to different countries had different set ups/equipment, and it'll help when answering questions etc. in the future...
1 - 5 of 5 Posts
Join the discussion
Recommended Reading
-
Driveshaft Tailshaft clearance
Alfetta & GTV6 (1972-1986)Does anyone have a spec or close measurement of the clearance of the driveshaft and tailshaft? My tailshaft bushing has collapsed and I want to wedge some rubber in there until I can replace it. I did use a piece of fuel hose, and the two were touching. I cut the hose length wise and it was...- 8
- 263
-
iachella · updated
-
Horn will not quit!
Alfetta & GTV6 (1972-1986)Seeking advice on a horn that blows constantly. Background: I replaced the steering wheel on my 86 GTV6 with an aftermarket similar to a Nardi. Prior to the steering wheel removal the horn was inoperative. With the new wheel, I made a shim for the copper ring to make it extend far enough to...- 18
- 855
-
No Start 2L SPICA Alfetta Sedan
Alfetta & GTV6 (1972-1986)I got this Alfetta Sedan a while back and want to see if I can get it running. The PO said it needed a fuel pump, but when I put 12v directly to the pump it runs. When I turn the key to run, there is no power to the fuel pump. Is there a relay, which one? Which one of the bullet fuses is for...- 11
- 370
-
1976 Alfetta GT
Alfetta & GTV6 (1972-1986)I am considering the purchase of a 1976 Alfetta GT. The car is a completely stock survivor with the original paint and very little rust. The car looks nice and runs well with the only real flaw being torn front seats. The Spica pump was rebuilt by Wes Ingram and works fine. For a driver, the car...- 7
- 89
-
new member
Alfetta & GTV6 (1972-1986)just joined. going to see a 1983 alfetta gtv6 what should i look for ,owner said the is some rust but runs great- 10
- 63
Join now to ask and comment!