Alfa Romeo Forums banner
1 - 8 of 8 Posts

·
Registered
Joined
·
373 Posts
Discussion Starter · #1 ·
Hi, I've searched the board to no avail so I was hoping someone might be able to help. I am swapping out my old console for a somewhat better used one, and everything is good to go except for the hazard switch. Mine is a 78 Spider so it has the round push button type with a light inside the red button.

I was stupid and just yanked all the wires trusting that the wiring diagram would guide me. But the diagram I have (the color-coded ones provided to many on this forum) lists only four connections for my hazard button:

49A-White/Black
L - Blue/Black
R - Blue
31 - Black

But these connections alone do not work. Also, I'm 99 percent sure that many more than four of the posts on the switch were filled (maybe all of them, I'm not sure.) There are a lot of extra wires floating around in the console area, partly because I don't have some lights like ExhTemp hooked up, but also I suspect because some of them need to be hooked to the Hazard button.

If anyone has any info or advice, I'd appreciate it. I hate to put it back together worse than before.
 

·
Registered
Joined
·
373 Posts
Discussion Starter · #3 ·
The signals work. The hazards worked great before I bumbled along.

I will try your test in the morning; what will that tell me?
 

·
Registered
Joined
·
373 Posts
Discussion Starter · #5 · (Edited)
Ok. But it seems unlikely that the switch would suddenly die now. What I'm curious about are the other prongs on the switch which were previously occupied when it worked -- is there an alternate wiring possibility? It was definitely working before with all or most of the prongs in use. I'm just kicking myself for being so rash.
 

·
Registered
Joined
·
373 Posts
Discussion Starter · #8 ·
Oops, yes, this is the same switch I had in previous console, moved over to the newer one.
 

·
Registered
Joined
·
373 Posts
Discussion Starter · #9 ·
Well, first the test--three wires you mentioned put together--produced no signal lights. And now things have gone further downhill: First fuses #3 and #6 blew, so I unhooked the hazard switch altogether, and now fuse #6 keeps blowing again.

At this point I"m out of 8 amp fuses and out of my depth, so I'm probably going to just send it off to my mechanic since I needed to tend to some other items anyway. Which is a tragedy given the spring weather we're having here...
 

·
Registered
Joined
·
373 Posts
Discussion Starter · #11 ·
I hear you, and I know you're right. But the cost issue is why I tried to handle this myself and I already turned a half day job into nearly two days-- some of us just aren't up to this stuff I'm afraid. I've got family stuff to take care of etc, so it's worth it to me to farm this out at this point.

I really do appreciate your help, though.
 

·
Registered
Joined
·
373 Posts
Discussion Starter · #12 ·
Well, Roadtrip I owe you a debt. Despite what I declared in the previous message, your encouragement prompted me to recheck again and I found the problem (wrong connection). I now appear to be good to go, though the hazard switch still isn't working but I'll leave that for now. Many thanks...
 

·
Registered
Joined
·
373 Posts
Discussion Starter · #13 ·
...And then I go for a test drive and a new problem: turn signals prompt the hazards! Judging from the wire diagram I'm betting it's a wrong white/black wire. I'll dig into it later and hope I don't get nabbed for not using my signal in the meantime...
 
1 - 8 of 8 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top