Alfa Romeo Forums banner

FS: 71 Spider Parting Out

3142 Views 29 Replies 10 Participants Last post by  Alfa Romeo Red
I reluctantly am abandoning a 1971 Spider restoration project due to excessive rust in the rockers and front/rear sides. We had done all the mechanical work beforehand and some I will reuse. Most parts available are listed below and are in good condition. If there is something not listed that you need, send me a pm.
My intent is to sell at very reasonable prices to help relieve me of extra parts and provide for your project. I have placed prices on some parts. The rest are up for an offer (via pm). I will also consider best offer for those with a price.

The car is near Seattle and I'm in the Portland area so I am not easily able to provide pictures. Here's the list:

Carello Headlight Covers Kit Complete and New - $240
Headlight trim rings
Front and Rear Bumpers - $800
Wiper assembly, wiper motor - $220
Washer bag
Hood release hardware, trunk release hardware
Windshield - $90 (has repairable scratches)
Doors w/ all glass and Door Handles(exterior) - $220 for both
Hood and Trunk Lid - $200 for both
Door Panels - Interior - $110 for both
Window winders, door handles - Int. - $100
Dash, gauges, ignition switch, turn signal/headlamp stalk
Handbrake assembly, handbrake boot, seatbelts, sunvisors
Front, center and side rubber mats, trunk mat
Rear section mats and apron pcs, plastic trim pcs
Rearview mirror
Radiator
Radiator Overflow bottle
Ignition coil
Stayfast Top and Frame
External stainless trim pcs, Internal trim pcs - door jam area
Driveline, donuts - $150
Rear end assembly - $230
Steering Box - $550
Exhaust center and rear sections
Brakes - calipers, rotors, spindles
Seat belts and attach loop
Console - top and side pcs
Grill
Taillight assemblies and side markers
Brake pedal assembly

Thanks,
Russ
See less See more
1 - 20 of 30 Posts
spider parts

Hi, can use front and rear calipers if in very good useable condition with no issues. Also rubber mats in good condition and washer bag. have 72 that needs some stuff. Price on canvas top also please. 321-214-4190 Florida I have lots of parts also if you need anything to trade.
Bob
spider parts

I'd be interested in the console parts, seat belts, and a glove box door if you have one. I have a 79 spider I'm assuming they'd fit...Thanks!
alfa parts

Hi, have seat belts and console parts. What do you need specifically?
Bjeck,
I don't think the 79 and 71 belts or console are alike. They could be made to work but would not be as current. Which pcs of console are needed?

Russ
any chance you have a wooden personal steering wheel without cracks? thanks.
alfa parts

Bjeck,
I don't think the 79 and 71 belts or console are alike. They could be made to work but would not be as current. Which pcs of console are needed?

Russ
Hi, I have parts from more than 1 year car. I need to know what you need so that I can see if I have them. Bob
parts

I need the section that fits around the shifter...looks like this Alfa Romeo and Fiat Reproduction Consoles
as well as both halves of the seat belt assemblies. Thanks so much...I could also use the round air vent cover that is by the passenger's left knee.
Refreshing this list of parts...
Here is an updated list of remaining items:

Headlight trim rings
Wiper assembly, wiper motor - $200
Washer bag
Hood release hardware, trunk release hardware
Windshield - $90 (has repairable scratches)
Doors w/ all glass - $180 for both
Hood and Trunk Lid - $200 for both
Door Panels - Interior - $110 for both
Window winders, door handles - Int. - $100
Dash, gauges, ignition switch, turn signal/headlamp stalk
Handbrake assembly, seatbelts
Front, center and side rubber mats
Rear section mats and apron pcs, plastic trim pcs
Rearview mirror
Radiator
Ignition coil
Stayfast Top and Frame
External stainless trim pcs, Internal trim pcs - door jam area
Driveline, donuts - $150
Rear end assembly (not limited slip) - $210
Steering Box - $350
Exhaust center and rear sections
Brakes - calipers, rotors, spindles
Seat belts and attach loop
Taillight assemblies and side markers
Brake pedal assembly
Wheel well splash panels
Brake and clutch master and slave cyl. - $150
Springs, Koni shocks, complete lower A arms - $300
Personal Steering Wheel - $50 - needs refinish
See less See more
What shape is the dash in? If it is in good shape and not cracked, I'm interested. Let me know the price. Also, are the rubber mats in good shape? I'm looking for those too.
thanks, Paul
Hi...im looking for the battery tray and passenger side jack point....if possible cut off the car 6 inch arround area....also the b/tray will have to be cut off the car. Let me know and the price. Thanks
These areas of the body shell are still available. I can contact Daron at Vintage Customs and connect you guys. He'll cut the sections needed and ship. PM me if you'd like to pursue.
Thanks!
Here's a fresh updated list of remaining items:

Wiper assembly, wiper motor - $200
Hood release hardware, trunk release hardware
Hood and Trunk Lid - $200 for both
gauges -oil, temp, fuel
Side rubber mats
Handbrake assembly
plastic trim pcs
Rearview mirror
Radiator
Ignition coil
External stainless trim pcs, Internal trim pcs - door jam area
Driveline, donuts
Rear end assembly (not limited slip)
Steering Box -
Exhaust center and rear sections
Brakes - rotors, spindles
Taillight assemblies
Brake pedal assembly - hanging
Wheel well splash panels
Brake and clutch master and slave cyl.
Springs, Koni shocks, complete lower A arms
Personal Steering Wheel
See less See more
1750s....what is your phone number....so i can call you up.
71 Spider parts needed

Hi,

I'm restoring a 71 Spider and am looking for any of the following:

Trunk release hardware
gauges -oil, temp, fuel
Handbrake assembly
plastic trim pcs
Headlight rings
Headlight bucket assemblies
rear bumper

Thanks,
Stuff
See less See more
Headlight buckets

Hi, I have 2 good headlight buckets if you still need them. Where are you? Bob
Hi Stuff,
I have all but the bumper. I'm the original owner of this post. Not sure who Bob is who replied about buckets. Send me a PM and we can work out the details.

Thanks,
Russ
Hello Russ ,I need the spindles if they are for 1750-2000 type.Unfortunately I live in Romania (Europe) and for this reason I have also to ask from shipping cost.Tks for your interest.
Regards,
Serban
1 - 20 of 30 Posts
Top