Alfa Romeo Forums banner

Search results

1-20 of 287 Results
Advanced Search
  1. Throw Out Bearing Problem or More

    164 & 168 (1991-1995)
    John, It's not impossible to disconnect the gearbox and change the clutch yourself. I did it, and although it took me a while, I did get it done in my shed without mishap. My car had about 320K miles then. I even made a couple of guide pins to help slide it back in place - if you need to...
  2. Changing 24v water pump and resetting timing belt

    164 & 168 (1991-1995)
    Sorry, No I haven't yet, but someday soon I hope. Dennis
  3. Wanted 164 Left rear quarter panel

    Alfa Romeo Parts For Sale & Wanted
    I'm looking for a left (driver side) rear quarter panel for my 164. Contact [email protected] Thanks Dennis
  4. FS: 164 Body Parts

    Alfa Romeo Parts For Sale & Wanted
    I'm in need of a left rear quarter panel. Am I too late? Dennis. [email protected]
  5. Body parts in Kansas?

    164 & 168 (1991-1995)
    I'm in need of a left (driver) side door and a left rear quarter panel for my 164B. I had a meeting with an inattentive pickup driver.....and I lost. I've been looking for some time for them anywhere close to where I live so I can pick them up, but without much success. I live in South...
  6. What did you do Alfa related today?

    164 & 168 (1991-1995)
    Take a look at McMaster Carr catalog, they have ball joint ends in right and left hand thread. I am not sure about metric threads, buy I wouldn't balk at using SAE threads down there, where nobody can see them. ;) In SAE, it wouldn't be too hard to make up the center piece length to suit...
  7. BB2 back in the Alfa related news

    164 & 168 (1991-1995)
    Steve, Last time I changed the clutch master, I ended up super-gluing the clevis pin to the tip of my finger and only then got it into place. Needless to say getting loose from the pin was a careful job. Used the same procedure to put split pin in clevis pin, and then stopped for a cool one...
  8. What did you do Alfa related today?

    164 & 168 (1991-1995)
    Beeton, Are you sure the loss is at the brake MC, because if you have a manual transmission, the brake fluid reservoir also serves the clutch master, which is inside the car, right over the foot pedal area. The clutch MC is contained in a plastic cover, with an inner "sock" of foam plastic -...
  9. Rear Hub Source

    164 & 168 (1991-1995)
    Just put the number 82469109 into google, there'slots of possibilities!
  10. Alfa 164 Rear strut info

    164 & 168 (1991-1995)
    Hi Lost, When I put my struts back together, I fitted the spring in to the top rubber as you show in your second picture, with the end of the spring up tight to the space in the rubber. I'm not sure it makes much difference really, but I feel like that's what was intended when the...
  11. For Sale Parting 93 164 Speedlines..etc

    Alfa Romeo Parts For Sale & Wanted
    I need the left rear door and quarter panel if you still have them. Can you set up on a pallet for truck shipping? Thanks. Dennis.
  12. LED headlights and/or light bars

    164 & 168 (1991-1995)
    Mike D, Before you lay out about $400 for Euro lights, remember that Elma headlamps were designed to use H4 bulbs, and have clear lenses. It will only cost about $30 to try a set of the latest LED designs, which are very, very good and have flat cutoff that is as good or better than the H4...
  13. Alfa 164 V6 main engine mount

    164 & 168 (1991-1995)
    Richard, One point I see nobody has mentioned is that the nuts of the three bolts holding the "rear" engine mount are spot-welded to the frame, so you only need to use a socket(above) on the bolt itself. BTW, the "corner" bolt has a 13mm head, and the other two are 15mm, from memory. It...
  14. Getting close...

    164 & 168 (1991-1995)
    Mark, I think you're talking about the bearing in what is called the "Intermediate shaft" which goes across from the gearbox and connects with the right drive axle. I had the same concern with mine, it felt a little stiff but rolled smoothly. After looking at how to change the bearing - I...
  15. car stalled

    164 & 168 (1991-1995)
    Just a couple of quickies, since the "gurus" haven't responded yet. Check inside the distributor cap, look especially at the little carbon button in the center. Be careful to fit it back carefully BEFORE you tighten the screws. DAMHIKT. Then the fuel - not so easy, but without fuel it won't...
  16. Cloth Interior

    164 & 168 (1991-1995)
    Resurrecting this old posting to ask if there's anyone who can suggest how I might re-stitch the center seam at top center of the rear seat. 91B - Gray fabric seats. I can take it out, of course, and get it done - but I'm a dedicated do-it-yourselfer. AKA cheap! Any ideas? Dennis
  17. Engine rebuild manuals, And parts.

    164 & 168 (1991-1995)
    Spencerider, Since it sounds as if you're going to undertake an engine rebuild, I suggest you take a look here - https://www.alfabb.com/bb/forums/164-168-1991-1995/482185-12v-euro-cam-pulley-belt-upgrade.html Perhaps the main worry with this engine is its timing belt, and the fact that it is...
  18. Sunroof help!

    164 & 168 (1991-1995)
    The left button opens the slide, the right button closes it. When it's already closed, the right button pops it up and the left button closes it down. If not, sounds like the paint got to the sunroof seal. How to beak it free........I think I would go to the hardware shop and buy some wooden...
  19. Sunroof help!

    164 & 168 (1991-1995)
    To pop down the sunroof control panel, pry gently at the right rear corner. Gently! While it's down is a good time to give each of the control buttons a shot of Deoxit D5 to clean the contacts.
1-20 of 287 Results
Top