Alfa Romeo Bulletin Board & Forums - Search Results
Advanced Search
Showing results 1 to 15 of 15
Search took 0.01 seconds.
Search: Posts Made By: alfavulcan
Forum: Gearbox, Transaxle, Differential & Propshaft   12-19-2011, 07:51 PM
Replies: 96
Views: 18,487
Posted By alfavulcan
its quite possible some careful sheetmetal...

its quite possible some careful sheetmetal contouring [ with a big ole hammer] could get any clearance needed, mine was too tight top left because of being shifted a little to the left
Forum: Gearbox, Transaxle, Differential & Propshaft   12-19-2011, 02:38 PM
Replies: 96
Views: 18,487
Posted By alfavulcan
p.s. i totally agree on DON'T paint the tranny,...

p.s. i totally agree on DON'T paint the tranny, except maybe a silver. i prefer just cleaned very well. i checked out several before pulling the one i bought, none were painted, most looked like they...
Forum: Gearbox, Transaxle, Differential & Propshaft   12-19-2011, 02:31 PM
Replies: 96
Views: 18,487
Posted By alfavulcan
to clarify the tunnel issue, i did not cut my...

to clarify the tunnel issue, i did not cut my trans tunnel for the shifter location, the wider flat section top driver's side interfered w/tunnel. the 115 chassis has the tunnel offset about an inch...
Forum: Gearbox, Transaxle, Differential & Propshaft   12-18-2011, 06:15 PM
Replies: 96
Views: 18,487
Posted By alfavulcan
on mine i am welding in new sheetmetal. the only...

on mine i am welding in new sheetmetal. the only t5 i am aware of with the s-10 style shifter is the s-10/s-15. the gear ratios all wrong, shorter input and not WC. the only way is to combine the...
Forum: Gearbox, Transaxle, Differential & Propshaft   12-17-2011, 12:23 PM
Replies: 96
Views: 18,487
Posted By alfavulcan
with bianchi's kit, 94-95 mustangs [ t-bird?]...

with bianchi's kit, 94-95 mustangs [ t-bird?] gearbox is what you want. v6 and v8 box first is 3.35, fifth is .68 on v8, .72 on v6. a couple of sites i've checked, most notable a volvo swap, thought...
Forum: Gearbox, Transaxle, Differential & Propshaft   12-15-2011, 01:45 PM
Replies: 96
Views: 18,487
Posted By alfavulcan
actually 94 1/2 mustang t5 from a v6 car, easy to...

actually 94 1/2 mustang t5 from a v6 car, easy to find, mine was $150 at a pick a part, longer input is what bianchi uses, earlier shorter input could be used if adapter bellhousing length were kept...
Forum: Gearbox, Transaxle, Differential & Propshaft   12-15-2011, 01:39 PM
Replies: 96
Views: 18,487
Posted By alfavulcan
i am using a 95 mustang t-5 with the rear mount...

i am using a 95 mustang t-5 with the rear mount shifter. i have just mocked mine up with one of larry dickmans v6 bellhousings. i haven't yet machined mine or mounted it yet as i've not been home...
Forum: Gearbox, Transaxle, Differential & Propshaft   12-14-2011, 05:33 PM
Replies: 96
Views: 18,487
Posted By alfavulcan
i have one of bianchi's t5 kits. it does require...

i have one of bianchi's t5 kits. it does require some machining of the bellhousing as the t5 input and front bearing retainer is a little bit larger
Forum: Gearbox, Transaxle, Differential & Propshaft   06-22-2010, 03:42 PM
Replies: 96
Views: 18,487
Posted By alfavulcan
i guess every project requires at least one other...

i guess every project requires at least one other project to finish.
Forum: Gearbox, Transaxle, Differential & Propshaft   06-22-2010, 02:56 PM
Replies: 96
Views: 18,487
Posted By alfavulcan
Forum: Gearbox, Transaxle, Differential & Propshaft   06-22-2010, 02:23 PM
Replies: 96
Views: 18,487
Posted By alfavulcan
was cutting out the tunnel required for trans...

was cutting out the tunnel required for trans tunnel clearance? i understand that a new hole for the rear shifter [which i like] was required. how close was it? too much for a bfh?
Forum: Gearbox, Transaxle, Differential & Propshaft   06-12-2010, 03:28 PM
Replies: 96
Views: 18,487
Posted By alfavulcan
I ain't skeered, show'em

I ain't skeered, show'em
Forum: Gearbox, Transaxle, Differential & Propshaft   05-24-2010, 08:45 PM
Replies: 96
Views: 18,487
Posted By alfavulcan
speedometer

one thing i've been looking at is the speedo drive. i have a 94 v6 mustang trans and i think it uses an electronic sender for the speedometer. i haven't really looked too close [ haven't taken it...
Forum: Gearbox, Transaxle, Differential & Propshaft   05-12-2010, 03:50 PM
Replies: 96
Views: 18,487
Posted By alfavulcan
is the machining for input shaft clearance? i...

is the machining for input shaft clearance? i slid a spider bellhousing over the input shaft of the t5 i picked up. it was a very close fit and really needed a little more clearance to rotate freely
Forum: Gearbox, Transaxle, Differential & Propshaft   04-24-2010, 09:34 PM
Replies: 96
Views: 18,487
Posted By alfavulcan
count me in. are you using the earlier ford short...

count me in. are you using the earlier ford short input shaft version of the t-5 or the later, around 94 up, version? i found a nice 94 v6 mustang t-5 cheap nearby but am concerned the input shaft...
Showing results 1 to 15 of 15

 
Forum Jump
 
For the best viewing experience please update your browser to Google Chrome