Alfa Romeo Bulletin Board & Forums - Reply to Topic
Thread: My Megasquirt recipe for Alfa Nord 4-cylinder Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Alfa Romeo Bulletin Board & Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
01-10-2019 07:01 AM
Alexofwareneck Jason would like to establish communication I copied your microsquirt install on alfa nord and have some questions my phone 804-815-8173
03-12-2018 06:17 PM
alfaparticle That is a cool plan. I look forward to hearing more about it.
I talked to a guy who installed programmable EFI with ITB's on a 911. He was running MAP with a plenum to combine the signals. It looks cool but it makes less power than my GTV6 with a stock single throttle body.
03-12-2018 01:54 PM
Originally Posted by alfaparticle View Post
Do you plan to use throttle position or a composite MAP signal for controlling fuelling?
I have a little bit experience tuning but this would be my first time with ITBs, I was reading up on it and the Megasquirt 3 software has a special mode for ITB that uses MAP for partial loads and TPS for WOT and higher loads. This seems like a good compromise for driveability and performance, I think I'm going to try it this way.
03-12-2018 09:47 AM
I am in the process of collecting parts to do the same except with ITBs.
Do you plan to use throttle position or a composite MAP signal for controlling fuelling?
03-12-2018 09:00 AM
ItalianSpidrMan This looks really great Jason, I am in the process of collecting parts to do the same except with ITBs. Would basically be the same installation except the injectors probably. Thank you for documenting your work.
09-12-2017 08:13 PM
alfaparticle My Megasquirt experience is with a V6 motor and there may be some differences. My 3L motor has a plenum and throttle body from a 2.5. The plenum has been modified for better air flow but the butterfly is stock. The original 2.5 motor made a little less than 160 HP and my motor with the same throttle body makes a little over 250 HP, so I don't think the throttle body is a limiting factor. You can always get more fuel by installing bigger injectors but I have yet to hear of anyone successfully controlling bigger injectors with an L-Jet computer. The route to high power with the V6 includes bigger injectors and Megasquirt or other programmable FI.
09-12-2017 07:32 PM
jarrington With my Megasquirt setup there is no AFM, which is the biggest airflow restriction. The stock plenum and throttle body are still a restriction compared to a set of Jenvey throttle bodies or similar but the plus side is that you get a much better vacuum signal from the plenum, which is a must when using a MAP sensor.

Unfortunately the Spider project has been shoved on the back burner due to a cabin build in the mountains, but once I have the roof on in a month or so I should have some time to get the Alfa dialed in.

09-12-2017 06:30 PM
john802 Ah, my mistake. I just received the book "How to Tune & Modify Bosch Fuel Injection" by Ben Watson. In the L Jet performance tuning section, it states that the primary problem with the stock L Jet is getting enough air into the engine, not fuel. On a stock system, the airflow meter peaks between 3000-3500 rpm. The book goes on to say the second airflow restriction is the stock throttle body and that larger throttle bodies can help with this problem. Only then does the book talk about fuel, and there are a few problems noted there as well. First, under acceleration, the engine is first starved for fuel because it takes time for the pressure to travel through the plumbing to signal the pressure meter to increase the fuel. Second, the stock fuel pressure can not deliver more fuel to the injectors above 3000 rpm. Anyway, that is what Ben Watson wrote in his book.
09-11-2017 08:10 AM
65Sprint As Ed points out, at some point air flow to the intake probably becomes a limiting factor in an L-Jet Spider as was the case in the 3L GTV6. But at what state of tune? 160hp? 180hp? Jason's effort may help answer that question.

I am running stock L-Jet with 10:1 (nominal) Motronic pistons and a set of Richard Jemison's cams in the '88 Spider. Recent tests confirm the L-Jet is able to maintain a wot AFR around 13:1 through 6500 rpm ... no lean mixture issues. Compared to Ed's and Jason's engines, my changes are quite mild but the car is much more enjoyable and for the first time in 29 years the engine likes to be revved above 5000 rpm.
09-11-2017 07:17 AM
alfaparticle L-Jet limits what you can do. A 3L V6 made an extra 30 HP when L-jet was replaced by Megasquirt due to increased airflow when the AFM was removed and improved fuel supply.
But L-Jet can handle a bit more airflow. 65Sprint has better cams in his L-jet spider.
09-11-2017 06:28 AM
john802 Ed, thank you for your reply. I have read a number of your comments on other threads and have learned a lot. In this case, I am still wondering. If the engine has performance cams with overlap and a lower back pressure exhaust system, those improvements would increase the volume of air the engine can take in and expel out, no? More air would flow through this modified engine that would flow through a stock engine, no? I am just wondering if the stock L Jet air intake system (throttle body, black tube across the engine, etc) would be restrictive. I have read somewhere else that the L Jet air intake system was actually designed to be somewhat restrictive over 4000 RPM for the stock L Jet to meet US emissions requirements. Thus my question, if the air flow isn't there for more fuel, how to larger injectors help and how do you get a power/performance increase? Thank you.
09-11-2017 05:59 AM
alfaparticle Megasquirt controls the ON time for the injectors. Larger injectors get less ON time. You may get a little less resolution at low power/rpm but you may not notice it.
09-11-2017 05:52 AM
john802 I am looking to wake up my 1988 Spider engine and found your document very helpful. I am no expert at all, just trying to piece it all together. I am wondering if the larger injectors will get enough air at mid range and WOT with the L Jet throttle body and plumbing to the intake plenum. You might not be able to really tell if this is the case until the engine is under load. What are your thoughts on this point? Thank you.
04-14-2017 11:54 AM
IanB This is an INCREDIBLY well documented...great work. Hats off.
04-04-2017 05:07 PM
65Sprint Indeed it should go. Breathing certainly won't be a problem.
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

For the best viewing experience please update your browser to Google Chrome